3M-Dyneon-PTFE-TFM-7A (Dry-as-molded)
3M-Dyneon-PTFE-TFM-7A (Dry-as-molded) material properties: Density 2.062 g/cm3, Young's modulus 0.91 GPa, Yield strength 28.6 MPa (representative value...
Overview
polymer · fluoropolymer — Dry-as-molded representative condition
Grade designation: 3M-Dyneon-PTFE-TFM-7A-DRY
3M-Dyneon-PTFE-TFM-7A; manufacturer/trade: 3M; curated real material/grade family record
Curated real material/grade record. 3M trade or supplier catalog grade retained from grade name. Property values are representative literature ranges; consult linked references, standards, and manufacturer datasheets for design allowables.
Key material properties
| Density | 2.062 g/cm3 |
|---|---|
| Young's modulus | 0.91 GPa |
| Yield strength | 28.6 MPa (representative value; grade and condition dependent) |
| Thermal conductivity | 0.246 W/mK |
| Heat resistance / melting point | 263.6 C |
Published property ranges
| Density (g/cm3) | CAMPUS Plastics: 1.978–2.124; MatWeb: 1.919–2.169; Polymer handbook: 1.961–2.105 |
|---|---|
| Young's modulus (GPa) | CAMPUS Plastics: 0.874–0.928; MatWeb: 0.812–0.975; Polymer handbook: 0.856–0.908 |
| Thermal conductivity (W/mK) | CAMPUS Plastics: 0.237–0.244; MatWeb: 0.198–0.274; Polymer handbook: 0.226–0.232 |
Ranges are representative values from the cited handbooks/datasheets; use manufacturer datasheets for design allowables.
Typical uses
- chemical-resistant lining
- Seals
- wire insulation
- semiconductor chemical parts
Frequently asked questions
What is the density of 3M-Dyneon-PTFE-TFM-7A (Dry-as-molded)?
The density of 3M-Dyneon-PTFE-TFM-7A (Dry-as-molded) is 2.062 g/cm3.
What is 3M-Dyneon-PTFE-TFM-7A (Dry-as-molded) used for?
3M-Dyneon-PTFE-TFM-7A (Dry-as-molded) is typically used for chemical-resistant lining, Seals, wire insulation and semiconductor chemical parts.
What condition does 3M-Dyneon-PTFE-TFM-7A-DRY refer to?
3M-Dyneon-PTFE-TFM-7A-DRY refers to the "Dry-as-molded" condition: Dry-as-molded representative condition.
What category of material is 3M-Dyneon-PTFE-TFM-7A (Dry-as-molded)?
3M-Dyneon-PTFE-TFM-7A (Dry-as-molded) is categorized as polymer (family: fluoropolymer).
Internal tools
Related materials
- Chemours-Teflon-ETFE-200 (Conditioned)
- Chemours-Teflon-ETFE-200 (Dry-as-molded)
- Chemours-Teflon-ETFE-EP-541 (Conditioned)
- Chemours-Teflon-ETFE-EP-541 (Dry-as-molded)
- Chemours-Teflon-ETFE-LM-740AP (Conditioned)
- Chemours-Teflon-ETFE-LM-740AP (Dry-as-molded)
- Ensinger-TECAFORM-AH-CF-PEEK (Conditioned)
- Ensinger-TECAFORM-AH-CF-PEEK (Dry-as-molded)
References
- Polymer Data Handbook / CAMPUS-style datasheet references (Polymer handbook)
- Polytetrafluoroethylene — PubChem compound entry (PubChem (NCBI))
- Polymer Data Handbook / CAMPUS-style datasheet references